Specifications of All Geared Heavy Duty Lathe Model Admit Between Centres Length Of Bed Floor Space Occupied (m.m.) Aprox. Weight in kgs. Aprox. Case Dimensions (m.m.) Nett. Gross               VGH - 1 1000 m.m. 2135 m.m. (7') 2660 x 1450 1500 1900 2850 x 1300 x 1600 VGH - 2 1600 m.m. 2745 m.m. (9') 3140 x 1450 1650 2150 3350 x 1300 x 1600 VGH - 3 1900 m.m. 3050 m.m. (10') 3500 x 1450 1900 2450 3700 x 1300 x 1600 VGH - 4 2500 m.m. 3660 m.m. (12') 4110 x 1450 2050 2650 4300 x 1300 x 1600 VGH - 5 3100 m.m. 4270 m.m. (14') 4720 x 1450 2350 2950 5000 x 1300 x 1600     Width of Bed 325 m.m. (13") Centre Height over flat bed ways 267 m.m. (10.5") Swing Over Bed 525 m.m. Swing Over Cross Slide 300 m.m. Swing In Gap 830 m.m. Length of Gap in front of Face Plate 200 m.m. Cross Slide travel 280 m.m Compound Slide travel 145 m.m OPTIONAL Spindle Speeds Nos. / RPM Range (Motor RPM 960) 12 20, 28, 35, 55, 75, 105, RPM 140, 190, 265, 360, 520, 705. RPM Spindle Mounting on Taper Roller Bearings FEEDS Nos. of Feeds / Range For Longitudinal 40 / 0.066 to 2 m.m. / rev. of spindle Fully norton Gearbox) Cross 40 / 0.0165 to 0.5 m.m. / rev. of spindle OPTIONAL ACCESSORIES Face plate Carrier plate steady rest follow rest Taper turning attachment motorised coolant pump with tank and fittings Rear tool post with extended cross slide Chuck back plates (Extra) Electricals (Motor, Panel board, Wirings, Push button Switches, V-belts and fittings) Electrical Switch shaft Electro Magnetic Padel Brake splash guard. MAIN SPINDLE :   Type of Spindle Nose A 2-6 type Spindle Morse Taper MT - 6 Spindle Adapter Morse Taper MT - 4 Spindle Speeds Nos. / RPM Range (Motor RPM 1440) 12 30, 43, 55, 85, 115, 60, RPM 210, 285, 400, 545, 785, 1060. RPM TAIL STOCK SPINDLE : Diameter : 60.3 m.m. / Travel : 180 m.m. / Morse Taper : MT-4 LEADING SCREW : Diameter / Threads : 38 m.m. / 4 TPI THREADS THREADS     Nos. of Threads / Range Metric 24 / 0.5 m.m. To 15 m.m. Pitch (For Fully norton Gearbox) Inch 44 / 2 to 60 TPI ELECTRICALS Electirc motor of 3 HP / 2.25 k.w., 3 Phase, 1440 RPM with Panel board wirings, over load relay, Pushbutton switches, V-belts and fittings. STANDARD ACCESSORIES Flame Hardened bed ways Chuck back plate 1 no centre adapter Dead centres (MT - 4) 2 nos Tool Post Spanner Motor pulley Thread dial indicator Change gear set - 1 (For metric and inch both) and Norton gearbox Rigid Head Stock with Balanced Spindle Multi Thrading Norton Gear box and low Power friction at drive. Compact design and easy to operate with speed and feed changing Smoothly